Src. Channel Zap/1-1

Discussion in 'General' started by prasis, Sep 27, 2010.

  1. prasis

    Joined:
    Sep 23, 2010
    Messages:
    5
    Likes Received:
    0
    Recently I am experiencing the problem.

    On the main extension we get call from Unknown user ID and when pick up then just cutoff with some tone.

    I check the elastix report and show no source and src channel as Zap/1-1

    What most be problem ?

    below is the elastix report

    Date Source Destination Src. Channel Account Code Dst. Channel
    2010-09-27 10:09:16 300 Zap/1-1 SIP/300-xxxxxxxx
    2010-09-27 10:31:36 300 Zap/1-1 SIP/300-xxxxxxxx
    2010-09-27 10:34:24 300 Zap/1-1 SIP/300-xxxxxxxx
    2010-09-27 10:59:34 300 Zap/1-1 SIP/300-xxxxxxxx
    2010-09-27 11:53:32 300 Zap/1-1 SIP/300-xxxxxxxx
    2010-09-27 12:15:52 300 Zap/1-1 SIP/300-xxxxxxxx
     
  2. jgutierrez

    Joined:
    Feb 28, 2008
    Messages:
    5,737
    Likes Received:
    0
    Paste the CLI putput to see what is going on. Also I may think that it will be an issue related to your analog lines, there could be a wiring issue.
     
  3. prasis

    Joined:
    Sep 23, 2010
    Messages:
    5
    Likes Received:
    0
    I am not sure when you say CLI output. Are you looking for Asterisk-Cli if yes then what command to run.
     
  4. jgutierrez

    Joined:
    Feb 28, 2008
    Messages:
    5,737
    Likes Received:
    0
    Check the wiring of the anolog line, also test it by connencting an analog phone directly into it.
    I mean the CLI, for the output of:
    asterisk -r
     
  5. prasis

    Joined:
    Sep 23, 2010
    Messages:
    5
    Likes Received:
    0
    == Spawn extension (macro-dial, s, 7) exited non-zero on 'Zap/1-1' in macro 'dial'
    == Spawn extension (macro-dial, s, 7) exited non-zero on 'Zap/1-1'
    -- Executing [h@macro-dial:1] Macro("Zap/1-1", "hangupcall") in new stack
    -- Executing [s@macro-hangupcall:1] ResetCDR("Zap/1-1", "w") in new stack
    -- Executing [s@macro-hangupcall:2] NoCDR("Zap/1-1", "") in new stack
    -- Executing [s@macro-hangupcall:3] GotoIf("Zap/1-1", "1?skiprg") in new stack
    -- Goto (macro-hangupcall,s,6)
    -- Executing [s@macro-hangupcall:6] GotoIf("Zap/1-1", "0?skipblkvm") in new stack
    -- Executing [s@macro-hangupcall:7] NoOp("Zap/1-1", "Cleaning Up Block VM Flag: BLKVM/300/Zap/1-1") in new stack
    -- Executing [s@macro-hangupcall:8] DBdel("Zap/1-1", "BLKVM/300/Zap/1-1") in new stack
    -- DBdel: family=BLKVM, key=300/Zap/1-1
    -- Executing [s@macro-hangupcall:9] GotoIf("Zap/1-1", "1?theend") in new stack
    -- Goto (macro-hangupcall,s,11)
    -- Executing [s@macro-hangupcall:11] Hangup("Zap/1-1", "") in new stack
    == Spawn extension (macro-hangupcall, s, 11) exited non-zero on 'Zap/1-1' in macro 'hangupcall'
    == Spawn extension (macro-hangupcall, s, 11) exited non-zero on 'Zap/1-1'
    -- Hungup 'Zap/1-1'
     
  6. jgutierrez

    Joined:
    Feb 28, 2008
    Messages:
    5,737
    Likes Received:
    0
    Paste the output when the call enters your server, and when it was hangup
     

Share This Page