SIP/2.0 404 Not found Error

Discussion in 'General' started by arthurzhu, Nov 24, 2010.

  1. arthurzhu

    Joined:
    Nov 24, 2010
    Messages:
    2
    Likes Received:
    0
    I installed the software and configured connection, then completed General Setting and create SIP extensions. when I tried to test by eysBeam for internal test, I received error messages as below:

    16:23:05.4
    RECEIVING FROM: 192.168.1.110:5060
    SIP/2.0 404 Not found
    Via: SIP/2.0/UDP 192.168.1.102:9204;branch=z9hG4bK-d87543-a161587e217aa74f-1--d87543-;received=192.168.1.102;rport=9204
    From: "arthurzhu"<sip:8020@192.168.1.110>;tag=5952ed05
    To: "arthurzhu"<sip:8020@192.168.1.110>;tag=as4dc23f2b
    Call-ID: 235bf95b220b7a0f@QXJ0aHVyLVBD
    CSeq: 1 REGISTER
    Server: Asterisk PBX 1.6.2.13
    Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY, INFO
    Supported: replaces, timer
    Content-Length: 0


    16:23:05.4 Proxy slot #0 () - Failed to register! error-code: 404, msg: 'Not found'. Will no longer attempt registration for this SIP proxy target. AOR: '"arthurzhu"<sip:8020@192.168.1.110>', route-to: '<n/a>', firewall-proxy: 'F'.
    16:23:10.7 Proxy slot #1 () - Proxy not enabled
    16:23:10.7 Proxy slot #2 () - Proxy not enabled
    16:23:10.7 Proxy slot #3 () - Proxy not enabled
    16:23:10.7 Proxy slot #4 () - Proxy not enabled
    16:23:10.7 Proxy slot #5 () - Proxy not enabled
    16:23:10.8 Proxy slot #6 () - Proxy not enabled
    16:23:10.8 Proxy slot #7 () - Proxy not enabled
    16:23:10.8 Proxy slot #8 () - Proxy not enabled
    16:23:10.8 Proxy slot #9 () - Proxy not enabled

    My install environment:
    elastix-firstboot-2.0.0-14
    elastix-email_admin-2.0.0-23
    elastix-system-2.0.0-38
    elastix-asterisk-sounds-1.2.3-1
    elastix-2.0.0-57
    elastix-vtigercrm-5.1.0-8
    elastix-agenda-2.0.0-24
    elastix-fax-2.0.0-18
    elastix-reports-2.0.0-20
    elastix-a2billing-1.3.0-4
    elastix-addons-2.0.0-19
    elastix-pbx-2.0.0-40



    Who have this experience? Great appreciation!
     
  2. arthurzhu

    Joined:
    Nov 24, 2010
    Messages:
    2
    Likes Received:
    0
    Just scaned another same error and got the answer:

    I forgot one important step.... did not read the writing at the bottom of the page "Submit when done and don’t forget the red bar to apply the changes."
    I forgotten... I then used freePBX and the some how the Apply Configuration Changes hit me... I re-read the book and yes it was at the end of the page.

    Thanks. It is working now.
     

Share This Page