puertos FXS inicializa en Off-hook

Discussion in 'Elastix 2.x' started by Luis Diego, Feb 15, 2011.

  1. Luis Diego

    Joined:
    Nov 1, 2010
    Messages:
    237
    Likes Received:
    0
    . Uno de los puertos FXS inicializa en Off-hook y por lo tanto no funciona
    a. Este es el estatus del cannel

    pbx*CLI> dahdi show channel 132
    Channel: 132
    File Descriptor: 69
    Span: 5
    Extension:
    Dialing: no
    Context: from-internal
    Caller ID: 4132
    Calling TON: 0
    Caller ID name: Channel 132
    Mailbox: 4132
    Destroy: 0
    InAlarm: 0
    Signalling Type: FXO Kewlstart
    Radio: 0
    Owner: <None>
    Real: <None>
    Callwait: <None>
    Threeway: <None>
    Confno: -1
    Propagated Conference: -1
    Real in conference: 0
    DSP: no
    Busy Detection: no
    TDD: no
    Relax DTMF: yes
    Dialing/CallwaitCAS: 0/0
    Default law: ulaw
    Fax Handled: no
    Pulse phone: no
    DND: no
    Echo Cancellation:
    128 taps
    currently OFF
    Wait for dialtone: 0ms
    Actual Confinfo: Num/0, Mode/0x0000
    Actual Confmute: No
    Hookstate (FXS only): Offhook

    b. Este es el extracto del /var/log/messages
    Feb 15 07:43:48 pbx kernel: INFO-xpp: revision Unknown MAX_XPDS=64 (8*8)
    Feb 15 07:43:48 pbx kernel: INFO-xpp: FEATURE: without BRISTUFF support
    Feb 15 07:43:48 pbx kernel: INFO-xpp: FEATURE: with PROTOCOL_DEBUG
    Feb 15 07:43:48 pbx kernel: INFO-xpp: FEATURE: with sync_tick() from DAHDI
    Feb 15 07:43:48 pbx kernel: INFO-xpp_usb: revision Unknown
    Feb 15 07:43:48 pbx kernel: ACPI: PCI Interrupt 0000:00:1f.3 -> GSI 19 (level, low) -> IRQ 20
    Feb 15 07:43:48 pbx kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
    Feb 15 07:43:48 pbx kernel: usb 1-5: reset high speed USB device using ehci_hcd and address 2
    Feb 15 07:43:48 pbx kernel: INFO-xpp_usb: XUSB: Xorcom LTD -- Astribank -- FPGA
    Feb 15 07:43:48 pbx kernel: INFO-xpp: XBUS-00: [usb] Activating
    Feb 15 07:43:48 pbx kernel: usbcore: registered new driver xpp_usb
    Feb 15 07:43:48 pbx kernel: NOTICE-xpp: XBUS-00: packet_process: from 10 opcode=0x06: no such global command.
    Feb 15 07:43:48 pbx kernel: INFO-xpp: XBUS-00: DESCRIPTOR: 4 cards, protocol revision 30
    Feb 15 07:43:48 pbx kernel: INFO-xpp: XBUS-00: CARD 0 type=4.0 ports=4 (1x4), port-dir=0x00
    Feb 15 07:43:48 pbx kernel: INFO-xpp: XBUS-00: CARD 1 type=1.3 ports=8 (8x1), port-dir=0xFF
    Feb 15 07:43:48 pbx kernel: INFO-xpp: XBUS-00: CARD 2 type=1.3 ports=8 (8x1), port-dir=0xFF
    Feb 15 07:43:48 pbx kernel: INFO-xpp: XBUS-00: CARD 3 type=2.3 ports=8 (8x1), port-dir=0x00
    Feb 15 07:43:48 pbx kernel: ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
    Feb 15 07:43:48 pbx kernel: INFO-xpd_pri: revision Unknown
    Feb 15 07:43:48 pbx kernel: INFO-xpd_pri: FEATURE: WITHOUT DAHDI_AUDIO_NOTIFY
    Feb 15 07:43:48 pbx kernel: INFO-xpd_fxs: revision Unknown
    Feb 15 07:43:48 pbx kernel: INFO-xpd_fxs: FEATURE: with DIGITAL INPUTS support (polled every 1000 msec)
    Feb 15 07:43:48 pbx kernel: INFO-xpd_fxs: FEATURE: DAHDI_VMWI (HVAC only)
    Feb 15 07:43:48 pbx kernel: INFO-xpd_fxs: FEATURE: NO METERING Generation
    Feb 15 07:43:48 pbx kernel: INFO-xpd_fxo: revision Unknown
    Feb 15 07:43:48 pbx kernel: INFO-xpd_fxo: FEATURE: NO METERING Detection
    Feb 15 07:43:48 pbx kernel: hda_codec: ALC888: BIOS auto-probing.
    Feb 15 07:43:48 pbx kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
    Feb 15 07:43:48 pbx kernel: sd 1:0:0:0: Attached scsi generic sg1 type 0
    Feb 15 07:43:48 pbx kernel: INFO-xpd_pri: XBUS-00/XPD-00: Setting TDM to PRI
    Feb 15 07:43:48 pbx kernel: INFO-xpp: XBUS-00/XPD-00: Initialized: E1
    Feb 15 07:43:48 pbx kernel: INFO-xpd_pri: XBUS-00/XPD-01: Setting TDM to PRI
    Feb 15 07:43:48 pbx kernel: INFO-xpp: XBUS-00/XPD-01: Initialized: E1
    Feb 15 07:43:48 pbx kernel: INFO-xpd_pri: XBUS-00/XPD-02: Setting TDM to PRI
    Feb 15 07:43:48 pbx kernel: INFO-xpp: XBUS-00/XPD-02: Initialized: E1
    Feb 15 07:43:48 pbx kernel: INFO-xpd_pri: XBUS-00/XPD-03: Setting TDM to PRI
    Feb 15 07:43:48 pbx kernel: FDC 0 is a post-1991 82077
    Feb 15 07:43:48 pbx kernel: lp: driver loaded but no devices found
    Feb 15 07:43:48 pbx kernel: INFO-xpp: XBUS-00/XPD-03: Initialized: E1
    Feb 15 07:43:48 pbx kernel: rxt1: no version for "dahdi_hdlc_putbuf" found: kernel tainted.
    Feb 15 07:43:48 pbx kernel: INFO-xpp: XBUS-00/XPD-10: Initialized: FXS
    Feb 15 07:43:49 pbx init_card_1_30: XBUS-00/UNIT-2: Defaults from /etc/dahdi/xpp.conf
    Feb 15 07:43:49 pbx init_card_1_30: XBUS-00/UNIT-2: Found 8 SLICS (0 1 2 3 4 5 6 7)
    Feb 15 07:43:59 pbx kernel: INFO-xpp: XBUS-00/XPD-20: Initialized: FXS
    Feb 15 07:43:59 pbx init_card_2_30: XBUS-00/UNIT-3: Defaults from /etc/dahdi/xpp.conf
    Feb 15 07:44:00 pbx kernel: NOTICE-xpd_fxo: XBUS-00/XPD-30/0: debounced false ring (only 50 ticks)
    Feb 15 07:44:00 pbx kernel: NOTICE-xpd_fxo: XBUS-00/XPD-30/2: debounced false ring (only 50 ticks)
    Feb 15 07:44:00 pbx kernel: NOTICE-xpd_fxo: XBUS-00/XPD-30/3: debounced false ring (only 50 ticks)
    Feb 15 07:44:00 pbx init_card_2_30: XBUS-00/UNIT-3: Setting OPERMODE=FCC
    Feb 15 07:44:01 pbx kernel: INFO-xpp: XBUS-00/XPD-30: Initialized: FXO
    Feb 15 07:44:01 pbx kernel: INFO-xpp: XBUS-00: Initialized in 27.2 sec
    Feb 15 07:44:01 pbx 'astribank_hook'[2326]: Skip(online): No '/etc/dahdi/xpp_order'
    Feb 15 07:44:01 pbx 'astribank_hook'[2326]: Removing uneeded startup semaphore
    Feb 15 07:44:01 pbx kernel: NOTICE-xpd_pri: XBUS-00/XPD-00: Alarms: 0x0 (NONE) => 0x4 (YELLOW)
    Feb 15 07:44:01 pbx kernel: NOTICE-xpd_pri: XBUS-00/XPD-01: Alarms: 0x0 (NONE) => 0x4 (YELLOW)
    Feb 15 07:44:01 pbx kernel: NOTICE-xpd_pri: XBUS-00/XPD-02: Alarms: 0x0 (NONE) => 0x8 (RED)
    Feb 15 07:44:01 pbx kernel: NOTICE-xpd_pri: XBUS-00/XPD-03: Alarms: 0x0 (NONE) => 0x8 (RED)
    Feb 15 07:44:01 pbx kernel: INFO-xpd_pri: XBUS-00/XPD-00: Setting TDM to CAS
    Feb 15 07:44:01 pbx kernel: INFO-xpd_pri: XBUS-00/XPD-01: Setting TDM to CAS
    Feb 15 07:44:01 pbx kernel: INFO-xpd_pri: XBUS-00/XPD-02: Setting TDM to CAS
    Feb 15 07:44:01 pbx kernel: INFO-xpd_pri: XBUS-00/XPD-03: Setting TDM to CAS
    Feb 15 07:44:01 pbx modprobe: WARNING: /etc/modprobe.d/dahdi.conf line 4: ignoring bad line starting with 'options'
    Feb 15 07:44:02 pbx kernel: dahdi_echocan_oslec: Registered echo canceler 'OSLEC'
    Feb 15 07:44:02 pbx kernel: dahdi: Registered tone zone 27 (Mexico)
    Feb 15 07:44:02 pbx kernel: NOTICE-xpd_fxs: XBUS-00/XPD-10/7: Already offhook during open. OK.
    Feb 15 07:44:03 pbx kernel: NOTICE-xpd_pri: XBUS-00/XPD-00: Alarms: 0x4 (YELLOW) => 0x0 (NONE)
    Feb 15 07:44:03 pbx kernel: NOTICE-xpd_pri: XBUS-00/XPD-01: Alarms: 0x4 (YELLOW) => 0x0 (NONE)
    Feb 15 07:44:03 pbx modprobe: WARNING: /etc/modprobe.d/dahdi.conf line 4: ignoring bad line starting with 'options'

    2. Uno de los puertos FXO que se encontraba trabajando bien, se escucha muy bajito y termina por dejarse de escuchar la voz.
    a. En este caso hemos vuelto a correr el fxotune sin éxito, lo más extraño es que como te informo, éste estaba trabajando correctamente, alguna sugerencia?
    b. Este es el estatus del cannel

    pbx*CLI> dahdi show channel 144
    Channel: 144
    File Descriptor: 81
    Span: 7
    Extension:
    Dialing: no
    Context: from-zaptel
    Caller ID:
    Calling TON: 0
    Caller ID name:
    Mailbox: none
    Destroy: 0
    InAlarm: 0
    Signalling Type: FXS Kewlstart
    Radio: 0
    Owner: <None>
    Real: <None>
    Callwait: <None>
    Threeway: <None>
    Confno: -1
    Propagated Conference: -1
    Real in conference: 0
    DSP: no
    Busy Detection: no
    TDD: no
    Relax DTMF: yes
    Dialing/CallwaitCAS: 0/0
    Default law: ulaw
    Fax Handled: no
    Pulse phone: no
    DND: no
    Echo Cancellation:
    128 taps
    currently OFF
    Wait for dialtone: 0ms
    Actual Confinfo: Num/0, Mode/0x0000
    Actual Confmute: No
    Hookstate (FXS only): Offhook
     
  2. jgutierrez

    Joined:
    Feb 28, 2008
    Messages:
    5,737
    Likes Received:
    0
    Cuál es el problema como tal? que se escucha bajo por un puerto?
    Si es así, ya intentaste revisar la línea? Ya cambiaste de puerto?

    Si el etma del volumen bajo es a nivel de todas las líneas, puedes editar
    /etc/asterisk/chan_dahdi.conf
    Y aumentar las ganacias de rx y tx a 1.5
    Luego desde la consola ejecutas:
    asterisk -rx "module reload"

    NOTA:
    Si estás pensando en aumentar acda vez más esos valores NO lo hagas, ocasionarás eco y en algunos casos asterisk pensará que ya has colgado mientras la sigue hablando y te cortará la llamada.
     
  3. fmvillares

    Joined:
    Sep 8, 2007
    Messages:
    1,785
    Likes Received:
    0
    on hook es colgado off hook es descolgado si te detecta mal es que algo en el cableado quizas este mal o te falta algo mas....la linea esta probada con un telefono comun?
     
  4. dicko

    Joined:
    Oct 24, 2008
    Messages:
    4,099
    Likes Received:
    0
    Antes que nada, compruebe si hay patas dobladas o corrosión en el RJ11 (2 y 3) en el Xorcom o cortocircuitos o corrosión en el cableado RJ21X (naranja/rojo / rojo/naranja)
     
  5. Luis Diego

    Joined:
    Nov 1, 2010
    Messages:
    237
    Likes Received:
    0
    muchas gracias mañana a primera hora revisare las patitas y retroalimento al Foro.
     
  6. Luis Diego

    Joined:
    Nov 1, 2010
    Messages:
    237
    Likes Received:
    0
    Es en el puerto A18 y no tengo conectado nada, esta libre pero el let esta en verde como si estuviera funcionando, y revise las patitas internas pero aparentemente todo esta normal y no estan dobladas
     
  7. dicko

    Joined:
    Oct 24, 2008
    Messages:
    4,099
    Likes Received:
    0
    Probablemente un fallo de hardware, póngase en contacto Xorcom
     
  8. Luis Diego

    Joined:
    Nov 1, 2010
    Messages:
    237
    Likes Received:
    0
    Ya se hizo el reporte, pero aun no me contestan nada esperaba que aca me den alguna sugerencia, bueno gracias de todos modos.
     

Share This Page