Pb d'envoi de fax via winprint et hylafax

Discussion in 'Elastix 2.x' started by pat1, Feb 12, 2009.

  1. pat1

    Joined:
    Jan 20, 2009
    Messages:
    68
    Likes Received:
    0
    Bonjour,
    Je n'arrive pas a envoyer des fax avec winprint et hylafax (pour info,la reception fonctionne )
    Ma configuration un trunk sip vers le fournisseur de voip IPPI
    J'ai installe un fax virtuel sur elastix
    j'ai telechargé et installé le client winprint , je l'ai autorisé sur le serveur
    Lors de l'envois, elastix fait 3 essais d'envois (je vois 3 numérotation successive vers mon trunk dans les logs,) mais le fax n'arrive jamais.
    Je recois par mail du seveur de fax ce compte rendu de l'echec .
    Quelqu'un peut il m'aider a le dechiffrer et a voir d'ou vient le pb

    Your job to 90468346544 failed because:
    Unspecified Transmit Phase C error; Giving up after 3 attempts to send same page
       ---- Transcript of session follows ----
    Feb 12 11:43:14.44: [ 3519]: SESSION BEGIN 000000006 33490468346544
    Feb 12 11:43:14.44: [ 3519]: HylaFAX (tm) Version 4.3.3
    Feb 12 11:43:14.44: [ 3519]: SEND FAX: JOB 1 DEST 90468346544 COMMID 000000006 DEVICE '/dev/ttyIAX1' FROM 'fax <mail.pat@orange.fr>' USER fax
    Feb 12 11:43:14.44: [ 3519]: STATE CHANGE: RUNNING -> SENDING
    Feb 12 11:43:14.44: [ 3519]: <-- [12:AT+FCLASS=1\r]
    Feb 12 11:43:14.44: [ 3519]: --> [2]
    Feb 12 11:43:14.44: [ 3519]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
    Feb 12 11:43:14.44: [ 3519]: DIAL 90468346544
    Feb 12 11:43:14.44: [ 3519]: <-- [16:ATDT90468346544\r]
    Feb 12 11:43:24.47: [ 3519]: --> [7]
    Feb 12 11:43:25.05: [ 3519]: --> [4:DE F9 10 03]
    Feb 12 11:43:25.05: [ 3519]: --> [5]
    Feb 12 11:43:25.05: [ 3519]: MODEM Command error
    Feb 12 11:43:25.05: [ 3519]: FCS error
    Feb 12 11:43:25.05: [ 3519]: <-- [9:AT+FRS=7\r]
    Feb 12 11:43:26.33: [ 3519]: --> [2]
    Feb 12 11:43:26.33: [ 3519]: <-- [9:AT+FTH=3\r]
    Feb 12 11:43:26.33: [ 3519]: --> [7]
    Feb 12 11:43:26.33: [ 3519]: <-- HDLC<3:FF C8 D8>
    Feb 12 11:43:27.50: [ 3519]: --> [2]
    Feb 12 11:43:27.50: [ 3519]: SEND send CRP (command repeat)
    Feb 12 11:43:27.50: [ 3519]: <-- [9:AT+FRH=3\r]
    Feb 12 11:43:29.68: [ 3519]: --> [7]
    Feb 12 11:43:31.33: [ 3519]: --> HDLC<25:FF C0 02 04 A6 4E AE 2E 36 AE C6 96 4E E6 82 04 A6 4E 46 B6 86 17 A4 63 9F>
    Feb 12 11:43:31.33: [ 3519]: --> [5]
    Feb 12 11:43:31.33: [ 3519]: MODEM Command error
    Feb 12 11:43:31.33: [ 3519]: FCS error
    Feb 12 11:43:31.33: [ 3519]: <-- [9:AT+FRS=7\r]
    Feb 12 11:43:31.75: [ 3519]: --> [2]
    Feb 12 11:43:31.75: [ 3519]: <-- [9:AT+FTH=3\r]
    Feb 12 11:43:31.76: [ 3519]: --> [7]
    Feb 12 11:43:31.76: [ 3519]: <-- HDLC<3:FF C8 D8>
    Feb 12 11:43:32.94: [ 3519]: --> [2]
    Feb 12 11:43:32.94: [ 3519]: SEND send CRP (command repeat)
    Feb 12 11:43:32.94: [ 3519]: <-- [9:AT+FRH=3\r]
    Feb 12 11:43:35.07: [ 3519]: --> [7]
    Feb 12 11:43:36.75: [ 3519]: --> HDLC<25:FF C0 02 04 A6 4E AE 2E 36 AE C6 96 4E E6 82 04 A6 4E 46 B6 86 16 C2 91 8E>
    Feb 12 11:43:36.75: [ 3519]: --> [2]
    Feb 12 11:43:36.75: [ 3519]: REMOTE CSI "Chambre Agriculture"
    Feb 12 11:43:36.75: [ 3519]: <-- [9:AT+FRH=3\r]
    Feb 12 11:43:37.15: [ 3519]: --> [7]
    Feb 12 11:43:37.15: [ 3519]: --> HDLC<12:FF C8 01 00 77 5F 01 79 03 C0 BC A1>
    Feb 12 11:43:37.17: [ 3519]: --> [2]
    Feb 12 11:43:37.17: [ 3519]: REMOTE best rate 14400 bit/s
    Feb 12 11:43:37.17: [ 3519]: REMOTE max A3 page width (303 mm)
    Feb 12 11:43:37.17: [ 3519]: REMOTE max unlimited page length
    Feb 12 11:43:37.17: [ 3519]: REMOTE best vres 7.7 line/mm
    Feb 12 11:43:37.17: [ 3519]: REMOTE format support: MH, MR
    Feb 12 11:43:37.17: [ 3519]: REMOTE best 0 ms/scanline
    Feb 12 11:43:37.17: [ 3519]: USE 14400 bit/s
    Feb 12 11:43:37.17: [ 3519]: SEND file "docq/doc1.ps;c1"
    Feb 12 11:43:37.17: [ 3519]: USE A4 page width (215 mm)
    Feb 12 11:43:37.17: [ 3519]: USE unlimited page length
    Feb 12 11:43:37.17: [ 3519]: USE 7.7 line/mm
    Feb 12 11:43:37.17: [ 3519]: USE 2-D MR
    Feb 12 11:43:37.17: [ 3519]: USE 0 ms/scanline
    Feb 12 11:43:37.17: [ 3519]: SEND training at v.17 14400 bit/s
    Feb 12 11:43:37.17: [ 3519]: <-- [9:AT+FRS=7\r]
    Feb 12 11:43:37.27: [ 3519]: --> [2]
    Feb 12 11:43:37.27: [ 3519]: <-- [9:AT+FTH=3\r]
    Feb 12 11:43:37.27: [ 3519]: --> [7]
    Feb 12 11:43:37.27: [ 3519]: <-- HDLC<23:FF C0 C2 6C 6C 82 C2 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04>
    Feb 12 11:43:38.98: [ 3519]: --> [7]
    Feb 12 11:43:38.98: [ 3519]: <-- HDLC<6:FF C8 C1 00 47 1E>
    Feb 12 11:43:39.38: [ 3519]: --> [2]
    Feb 12 11:43:39.38: [ 3519]: <-- [9:AT+FTS=7\r]
    Feb 12 11:43:39.48: [ 3519]: --> [2]
    Feb 12 11:43:39.48: [ 3519]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
    Feb 12 11:43:39.48: [ 3519]: <-- [11:AT+FTM=145\r]
    Feb 12 11:43:39.49: [ 3519]: --> [7]
    Feb 12 11:43:39.49: [ 3519]: DELAY 400 ms
    Feb 12 11:43:42.44: [ 3519]: --> [2]
    Feb 12 11:43:42.44: [ 3519]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
    Feb 12 11:43:42.44: [ 3519]: <-- [9:AT+FRH=3\r]
    Feb 12 11:43:43.23: [ 3519]: --> [7]
    Feb 12 11:43:44.07: [ 3519]: --> HDLC<5:FF C8 21 57 BE>
    Feb 12 11:43:44.07: [ 3519]: --> [2]
    Feb 12 11:43:44.07: [ 3519]: TRAINING succeeded
    Feb 12 11:43:44.07: [ 3519]: <-- [9:AT+FRS=7\r]
    Feb 12 11:43:44.15: [ 3519]: --> [2]
    Feb 12 11:43:44.15: [ 3519]: <-- [11:AT+FTM=146\r]
    Feb 12 11:43:44.16: [ 3519]: --> [7]
    Feb 12 11:43:44.16: [ 3519]: DELAY 400 ms
    Feb 12 11:43:44.56: [ 3519]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
    Feb 12 11:43:44.56: [ 3519]: SEND begin page
    Feb 12 11:43:44.58: [ 3519]: Reading MMR-compressed image file
    Feb 12 11:44:06.15: [ 3519]: SENT 44433 bytes of data
    Feb 12 11:44:06.15: [ 3519]: SEND 2D RTC
    Feb 12 11:44:06.15: [ 3519]: SEND end page
    Feb 12 11:44:06.47: [ 3519]: --> [10:NO CARRIER]
    Feb 12 11:44:06.47: [ 3519]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
    Feb 12 11:44:06.47: [ 3519]: Unspecified Transmit Phase C error
    Feb 12 11:44:06.47: [ 3519]: SEND: Unspecified Transmit Phase C error; Giving up after 3 attempts to send same page "docq/doc1.ps;c1", dirnum 0
    Feb 12 11:44:06.47: [ 3519]: <-- [9:AT+FTH=3\r]
    Feb 12 11:44:06.47: [ 3519]: --> [5]
    Feb 12 11:44:06.47: [ 3519]: MODEM input buffering enabled
    Feb 12 11:44:06.47: [ 3519]: <-- [5:ATH0\r]
    Feb 12 11:44:06.57: [ 3519]: --> [2]
    Feb 12 11:44:06.57: [ 3519]: MODEM set DTR OFF
    Feb 12 11:44:06.57: [ 3519]: MODEM set baud rate: 0 baud (flow control unchanged)
    Feb 12 11:44:06.57: [ 3519]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
    Feb 12 11:44:06.57: [ 3519]: SESSION END
    ------- Unsent job status -------
         Destination: 90468346544
               JobID: 1
             GroupID: 1
              Sender: fax
            Mailaddr: <span class="contextEntry" id="mail.pat@orange.fr_body">mail.pat@orange.fr</span>
              CommID: 000000006
               Modem: any
      Submitted From: 192.168.1.131
          Page Width: 209  (mm)
         Page Length: 296 (mm)
          Resolution: 196 (lpi)
              Status: Unspecified Transmit Phase C error; Giving up after 3 attempts to send same page
             Dialogs: 3
               Dials: 0
               Calls: 3
               Pages: 0
            TotPages: 1
            Attempts: 3
              Dirnum:


    Merci d'avance pour votre aide

    Patrick
     

Share This Page