IAXmodem: Inbound fine, outbound timeouts

Discussion in 'General' started by eleventeenth, Aug 15, 2007.

  1. eleventeenth

    Joined:
    Jul 30, 2007
    Messages:
    11
    Likes Received:
    0
    Hi,

    Inbound faxes are working without problem, but outbound faxes are timing out. I have trawled many forums, including this one and tried amny different things to get this working.

    we are using:
    * iaxmodem-0.1.14-1
    * asterisk-1.4.4-0


    This is using iaxmodem to an IAX extension, that goes out/in on an IAX trunk to our provider. We have 6 IAX modems setup (multiple clients, needed for billing) - all modems are exhibiting the same behavior. As mentioned, inbound faxes are working perfectly.

    Setup was completed as per the howto on this site.

    We have setup recording on the extensions (attached) and we are getting audio in both directions, at similar levels. Also, syslog logging of the modems has been setup (as found elsewhere on these forums).

    Logs are posted below - any help on all of this would be greatly appreciated as we have extended all avenues we can see available to us

    regards

    Chris McLean

    =======================================================
    Aug 15 08:56:30.91: [ 4682]: SESSION BEGIN 000000054 593049901924379230
    Aug 15 08:56:30.91: [ 4682]: HylaFAX (tm) Version 4.3.3
    Aug 15 08:56:30.91: [ 4682]: SEND FAX: JOB 19 DEST 9901924379230 COMMID 000000054 DEVICE '/dev/ttyIAX2' FROM 'fax <chris@eleventeenth.com>' USER fax
    Aug 15 08:56:30.91: [ 4682]: STATE CHANGE: RUNNING -> SENDING
    Aug 15 08:56:30.91: [ 4682]: <-- [12:AT+FCLASS=1\r]
    Aug 15 08:56:30.91: [ 4682]: --> [2]
    Aug 15 08:56:30.91: [ 4682]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
    Aug 15 08:56:30.91: [ 4682]: DIAL 9901924379230
    Aug 15 08:56:30.91: [ 4682]: <-- [18:ATDT9901924379230\r]
    Aug 15 08:56:47.07: [ 4682]: --> [7]
    Aug 15 08:56:47.73: [ 4682]: --> HDLC<16:FF C0 00 00 00 6A AA AA 00 11 09 01 BA 00 A5 46>
    Aug 15 08:56:47.73: [ 4682]: --> [5]
    Aug 15 08:56:47.73: [ 4682]: MODEM Command error
    Aug 15 08:56:47.73: [ 4682]: FCS error
    Aug 15 08:56:47.73: [ 4682]: <-- [9:AT+FRS=7\r]
    Aug 15 08:56:48.17: [ 4682]: --> [2]
    Aug 15 08:56:48.17: [ 4682]: <-- [9:AT+FTH=3\r]
    Aug 15 08:56:48.19: [ 4682]: --> [7]
    Aug 15 08:56:48.19: [ 4682]: <-- HDLC<3:FF C8 D8>
    Aug 15 08:56:48.19: [ 4682]: <-- data [3]
    Aug 15 08:56:48.19: [ 4682]: <-- data [2]
    Aug 15 08:56:49.37: [ 4682]: --> [2]
    Aug 15 08:56:49.37: [ 4682]: SEND send CRP (command repeat)
    Aug 15 08:56:49.37: [ 4682]: <-- [9:AT+FRH=3\r]
    Aug 15 08:56:56.37: [ 4682]: --> [0:]
    Aug 15 08:56:56.37: [ 4682]: MODEM <Empty line>
    Aug 15 08:56:56.37: [ 4682]: MODEM TIMEOUT: waiting for v.21 carrier
    Aug 15 08:56:56.37: [ 4682]: <-- data [1]
    Aug 15 08:56:56.37: [ 4682]: --> [2]
    Aug 15 08:56:56.37: [ 4682]: DELAY 200 ms
    Aug 15 08:56:56.57: [ 4682]: <-- [9:AT+FRH=3\r]
    Aug 15 08:57:01.53: [ 4682]: --> [7]
    Aug 15 08:57:02.99: [ 4682]: --> [10:NO CARRIER]
    Aug 15 08:57:02.99: [ 4682]: MODEM No carrier
    Aug 15 08:57:02.99: [ 4682]: <-- [9:AT+FRS=7\r]
    Aug 15 08:57:03.01: [ 4682]: --> [2]
    Aug 15 08:57:03.01: [ 4682]: <-- [9:AT+FTH=3\r]
    Aug 15 08:57:03.01: [ 4682]: --> [7]
    Aug 15 08:57:03.01: [ 4682]: <-- HDLC<3:FF C8 D8>
    Aug 15 08:57:03.01: [ 4682]: <-- data [3]
    Aug 15 08:57:03.01: [ 4682]: <-- data [2]
    Aug 15 08:57:04.19: [ 4682]: --> [2]
    Aug 15 08:57:04.19: [ 4682]: SEND send CRP (command repeat)
    Aug 15 08:57:04.19: [ 4682]: <-- [9:AT+FRH=3\r]
    Aug 15 08:57:11.19: [ 4682]: --> [0:]
    Aug 15 08:57:11.19: [ 4682]: MODEM <Empty line>
    Aug 15 08:57:11.19: [ 4682]: MODEM TIMEOUT: waiting for v.21 carrier
    Aug 15 08:57:11.19: [ 4682]: <-- data [1]
    Aug 15 08:57:11.19: [ 4682]: --> [2]
    Aug 15 08:57:11.19: [ 4682]: DELAY 200 ms
    Aug 15 08:57:11.39: [ 4682]: <-- [9:AT+FRH=3\r]
    Aug 15 08:57:18.39: [ 4682]: --> [0:]
    Aug 15 08:57:18.39: [ 4682]: MODEM <Empty line>
    Aug 15 08:57:18.39: [ 4682]: MODEM TIMEOUT: waiting for v.21 carrier
    Aug 15 08:57:18.39: [ 4682]: <-- data [1]
    Aug 15 08:57:18.39: [ 4682]: --> [2]
    Aug 15 08:57:18.39: [ 4682]: DELAY 200 ms
    Aug 15 08:57:18.59: [ 4682]: <-- [9:AT+FRH=3\r]
    Aug 15 08:57:25.60: [ 4682]: --> [0:]
    Aug 15 08:57:25.60: [ 4682]: MODEM <Empty line>
    Aug 15 08:57:25.60: [ 4682]: MODEM TIMEOUT: waiting for v.21 carrier
    Aug 15 08:57:25.60: [ 4682]: <-- data [1]
    Aug 15 08:57:25.61: [ 4682]: --> [2]
    Aug 15 08:57:25.61: [ 4682]: DELAY 200 ms
    Aug 15 08:57:25.81: [ 4682]: <-- [9:AT+FRH=3\r]
    Aug 15 08:57:32.81: [ 4682]: --> [0:]
    Aug 15 08:57:32.81: [ 4682]: MODEM <Empty line>
    Aug 15 08:57:32.81: [ 4682]: MODEM TIMEOUT: waiting for v.21 carrier
    Aug 15 08:57:32.81: [ 4682]: <-- data [1]
    Aug 15 08:57:32.81: [ 4682]: --> [2]
    Aug 15 08:57:32.81: [ 4682]: DELAY 200 ms
    Aug 15 08:57:33.01: [ 4682]: No answer (T.30 T1 timeout)
    Aug 15 08:57:33.01: [ 4682]: SEND FAILED: JOB 19 DEST 9901924379230 ERR No answer (T.30 T1 timeout)
    Aug 15 08:57:33.01: [ 4682]: <-- [9:AT+FTH=3\r]
    Aug 15 08:57:33.03: [ 4682]: --> [7]
    Aug 15 08:57:33.03: [ 4682]: <-- HDLC<3:FF C8 DF>
    Aug 15 08:57:33.03: [ 4682]: <-- data [3]
    Aug 15 08:57:33.03: [ 4682]: <-- data [2]
    Aug 15 08:57:34.21: [ 4682]: --> [2]
    Aug 15 08:57:34.21: [ 4682]: MODEM input buffering enabled
    Aug 15 08:57:34.21: [ 4682]: <-- [5:ATH0\r]
    Aug 15 08:57:34.31: [ 4682]: --> [2]
    Aug 15 08:57:34.31: [ 4682]: MODEM set DTR OFF
    Aug 15 08:57:34.31: [ 4682]: MODEM set baud rate: 0 baud (flow control unchanged)
    Aug 15 08:57:34.31: [ 4682]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
    Aug 15 08:57:34.31: [ 4682]: SESSION END

    =======================================================
    SYSLOG, from iaxmodems

    Aug 15 08:56:20 pbx FaxQueuer[4370]: SUBMIT JOB 19
    Aug 15 08:56:21 pbx FaxGetty[4436]: LOCKWAIT
    Aug 15 08:56:21 pbx FaxGetty[4436]: STATE CHANGE: RUNNING -> LOCKWAIT (timeout 30)
    Aug 15 08:56:22 pbx FaxSend[4682]: MODEM set DTR OFF
    Aug 15 08:56:22 pbx FaxSend[4682]: MODEM set baud rate: 0 baud (flow control unchanged)
    Aug 15 08:56:22 pbx FaxSend[4682]: DELAY 75 ms
    Aug 15 08:56:22 pbx FaxSend[4682]: MODEM set DTR ON
    Aug 15 08:56:22 pbx FaxSend[4682]: DELAY 2600 ms
    Aug 15 08:56:26 pbx FaxSend[4682]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF
    Aug 15 08:56:26 pbx FaxSend[4682]: DELAY 10 ms
    Aug 15 08:56:26 pbx FaxSend[4682]: MODEM flush i/o
    Aug 15 08:56:26 pbx FaxSend[4682]: <-- [4:ATZ\r]
    Aug 15 08:56:26 pbx FaxSend[4682]: --> [2]
    Aug 15 08:56:26 pbx FaxSend[4682]: DELAY 3000 ms
    Aug 15 08:56:29 pbx FaxSend[4682]: MODEM flush i/o
    Aug 15 08:56:29 pbx FaxSend[4682]: <-- [10:AT+VCID=1\r]
    Aug 15 08:56:29 pbx FaxSend[4682]: --> [9:AT+VCID=1]
    Aug 15 08:56:29 pbx FaxSend[4682]: --> [2]
    Aug 15 08:56:29 pbx FaxSend[4682]: <-- [7:ATS0=0\r]
    Aug 15 08:56:29 pbx FaxSend[4682]: --> [6:ATS0=0]
    Aug 15 08:56:29 pbx FaxSend[4682]: --> [2]
    Aug 15 08:56:29 pbx FaxSend[4682]: <-- [5:ATE0\r]
    Aug 15 08:56:29 pbx FaxSend[4682]: --> [4]
    Aug 15 08:56:29 pbx FaxSend[4682]: --> [2]
    Aug 15 08:56:29 pbx FaxSend[4682]: <-- [5:ATV1\r]
    Aug 15 08:56:29 pbx FaxSend[4682]: --> [2]
    Aug 15 08:56:29 pbx FaxSend[4682]: <-- [5:ATQ0\r]
    Aug 15 08:56:30 pbx FaxSend[4682]: --> [2]
    Aug 15 08:56:30 pbx FaxSend[4682]: <-- [7:ATS8=2\r]
    Aug 15 08:56:30 pbx FaxSend[4682]: --> [2]
    Aug 15 08:56:30 pbx FaxSend[4682]: <-- [8:ATS7=60\r]
    Aug 15 08:56:30 pbx FaxSend[4682]: --> [2]
    Aug 15 08:56:30 pbx FaxSend[4682]: <-- [12:AT+FCLASS=?\r]
    Aug 15 08:56:30 pbx FaxSend[4682]: --> [7:0,1,1.0]
    Aug 15 08:56:30 pbx FaxSend[4682]: --> [2]
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports "Data"
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports "Class 1"
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports "Class 1.0"
    Aug 15 08:56:30 pbx FaxSend[4682]: <-- [12:AT+FCLASS=1\r]
    Aug 15 08:56:30 pbx FaxSend[4682]: --> [2]
    Aug 15 08:56:30 pbx FaxSend[4682]: <-- [5:ATI3\r]
    Aug 15 08:56:30 pbx FaxSend[4682]: --> [19:www.soft-switch.org]
    Aug 15 08:56:30 pbx FaxSend[4682]: --> [2]
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM: Mfr http://www.soft-switch.org
    Aug 15 08:56:30 pbx FaxSend[4682]: <-- [5:ATI0\r]
    Aug 15 08:56:30 pbx FaxSend[4682]: --> [7]
    Aug 15 08:56:30 pbx FaxSend[4682]: --> [2]
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM: Model spandsp
    Aug 15 08:56:30 pbx FaxSend[4682]: <-- [9:AT+FTM=?\r]
    Aug 15 08:56:30 pbx FaxSend[4682]: --> [39:24,48,72,73,74,96,97,98,121,122,145,146]
    Aug 15 08:56:30 pbx FaxSend[4682]: --> [2]
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 3.85 line/mm
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 7.7 line/mm
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 15.4 line/mm
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports R16 x 15.4 line/mm
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 200 x 100 dpi
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 200 x 200 dpi
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 200 x 400 dpi
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 300 x 300 dpi
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 2400 bit/s
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 4800 bit/s
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 7200 bit/s
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 9600 bit/s
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 12000 bit/s
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 14400 bit/s
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports A4 page width (215 mm)
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports B4 page width (255 mm)
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports A3 page width (303 mm)
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports A4 page length (297 mm)
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports B4 page length (364 mm)
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports unlimited page length
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 1-D MH
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 2-D MR
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 2-D MMR
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports no ECM
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports T.30 Annex A, 64-byte ECM
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports T.30 Annex A, 256-byte ECM
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 0 ms/scanline
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 5 ms/scanline
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 10 ms, 5 ms/scanline
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 10 ms/scanline
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 20 ms, 10 ms/scanline
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 20 ms/scanline
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 40 ms, 20 ms/scanline
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM Supports 40 ms/scanline
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM http://www.SOFT-SWITCH.ORG spandsp/
    Aug 15 08:56:30 pbx FaxSend[4682]: <-- [5:ATM0\r]
    Aug 15 08:56:30 pbx FaxSend[4682]: --> [2]
    Aug 15 08:56:30 pbx FaxSend[4682]: STATE CHANGE: BASE -> RUNNING (timeout 30)
    Aug 15 08:56:30 pbx FaxSend[4682]: MODEM input buffering disabled
    Aug 15 08:56:30 pbx FaxSend[4682]: SEND FAX: JOB 19 DEST 9901924379230 COMMID 000000054 DEVICE '/dev/ttyIAX2' FROM 'fax <chris@eleventeenth.com>' USER fax
    Aug 15 08:57:33 pbx FaxSend[4682]: SEND FAILED: JOB 19 DEST 9901924379230 ERR No answer (T.30 T1 timeout)
    Aug 15 08:57:34 pbx FaxQueuer[4370]: NOTIFY: bin/notify "sendq/q19" "requeued" "" "08:58"
    Aug 15 08:57:34 pbx FaxQueuer[4370]: NOTIFY exit status: 0 (4702)
    Aug 15 08:57:50 pbx FaxQueuer[4370]: KILL JOB 19
    Aug 15 08:57:50 pbx FaxQueuer[4370]: NOTIFY: bin/notify "doneq/q19" "killed" ""
    Aug 15 08:57:50 pbx FaxQueuer[4370]: NOTIFY exit status: 0 (4786)
    Aug 15 08:57:52 pbx FaxGetty[4436]: MODEM set DTR OFF
    Aug 15 08:57:52 pbx FaxGetty[4436]: MODEM set baud rate: 0 baud (flow control unchanged)
    Aug 15 08:57:52 pbx FaxGetty[4436]: DELAY 75 ms
    Aug 15 08:57:52 pbx FaxGetty[4436]: MODEM set DTR ON
    Aug 15 08:57:52 pbx FaxGetty[4436]: DELAY 2600 ms
    Aug 15 08:57:56 pbx FaxGetty[4436]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF
    Aug 15 08:57:56 pbx FaxGetty[4436]: DELAY 10 ms
    Aug 15 08:57:56 pbx FaxGetty[4436]: MODEM flush i/o
    Aug 15 08:57:56 pbx FaxGetty[4436]: <-- [4:ATZ\r]
    Aug 15 08:57:56 pbx FaxGetty[4436]: --> [2]
    Aug 15 08:57:56 pbx FaxGetty[4436]: DELAY 3000 ms
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM flush i/o
    Aug 15 08:57:59 pbx FaxGetty[4436]: <-- [10:AT+VCID=1\r]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [9:AT+VCID=1]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [2]
    Aug 15 08:57:59 pbx FaxGetty[4436]: <-- [7:ATS0=0\r]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [6:ATS0=0]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [2]
    Aug 15 08:57:59 pbx FaxGetty[4436]: <-- [5:ATE0\r]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [4]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [2]
    Aug 15 08:57:59 pbx FaxGetty[4436]: <-- [5:ATV1\r]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [2]
    Aug 15 08:57:59 pbx FaxGetty[4436]: <-- [5:ATQ0\r]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [2]
    Aug 15 08:57:59 pbx FaxGetty[4436]: <-- [7:ATS8=2\r]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [2]
    Aug 15 08:57:59 pbx FaxGetty[4436]: <-- [8:ATS7=60\r]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [2]
    Aug 15 08:57:59 pbx FaxGetty[4436]: <-- [12:AT+FCLASS=?\r]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [7:0,1,1.0]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [2]
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports "Data"
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports "Class 1"
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports "Class 1.0"
    Aug 15 08:57:59 pbx FaxGetty[4436]: <-- [12:AT+FCLASS=1\r]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [2]
    Aug 15 08:57:59 pbx FaxGetty[4436]: <-- [5:ATI3\r]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [19:www.soft-switch.org]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [2]
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM: Mfr http://www.soft-switch.org
    Aug 15 08:57:59 pbx FaxGetty[4436]: <-- [5:ATI0\r]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [7]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [2]
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM: Model spandsp
    Aug 15 08:57:59 pbx FaxGetty[4436]: <-- [9:AT+FTM=?\r]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [39:24,48,72,73,74,96,97,98,121,122,145,146]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [2]
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 3.85 line/mm
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 7.7 line/mm
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 15.4 line/mm
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports R16 x 15.4 line/mm
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 200 x 100 dpi
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 200 x 200 dpi
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 200 x 400 dpi
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 300 x 300 dpi
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 2400 bit/s
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 4800 bit/s
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 7200 bit/s
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 9600 bit/s
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 12000 bit/s
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 14400 bit/s
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports A4 page width (215 mm)
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports B4 page width (255 mm)
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports A3 page width (303 mm)
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports A4 page length (297 mm)
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports B4 page length (364 mm)
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports unlimited page length
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 1-D MH
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 2-D MR
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 2-D MMR
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports no ECM
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports T.30 Annex A, 64-byte ECM
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports T.30 Annex A, 256-byte ECM
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 0 ms/scanline
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 5 ms/scanline
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 10 ms, 5 ms/scanline
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 10 ms/scanline
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 20 ms, 10 ms/scanline
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 20 ms/scanline
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 40 ms, 20 ms/scanline
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM Supports 40 ms/scanline
    Aug 15 08:57:59 pbx FaxGetty[4436]: MODEM http://www.SOFT-SWITCH.ORG spandsp/
    Aug 15 08:57:59 pbx FaxGetty[4436]: <-- [5:ATM0\r]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [2]
    Aug 15 08:57:59 pbx FaxGetty[4436]: <-- [9:AT+FAR=1\r]
    Aug 15 08:57:59 pbx FaxGetty[4436]: --> [2]
    Aug 15 08:57:59 pbx FaxGetty[4436]: STATE CHANGE: LOCKWAIT -> RUNNING (timeout 30)
     
  2. eleventeenth

    Joined:
    Jul 30, 2007
    Messages:
    11
    Likes Received:
    0
    sorry, attach didn't work - here it is again
     
  3. eleventeenth

    Joined:
    Jul 30, 2007
    Messages:
    11
    Likes Received:
    0
    and once more, the attach is over the max size - will email it if needed
     

Share This Page