how show zap/dahdi channel calling number

Discussion in 'General' started by callmgr, May 15, 2009.

  1. callmgr

    Joined:
    May 12, 2009
    Messages:
    4
    Likes Received:
    0
    hi,

    i setup a test scenario:

    an E1 connection between asterisk and ciscoCallMgr
    outgoing trunk is with 9 prefix.
    so when sipp(300) call 9400, the call will from trunk to ciscoCallMgr,
    and ciscoCallMgr will relay the call backto asterisk to another sipp(400).

    [300]
    sipp====>9400__ ==>400___
    \asterisk/ \ciscoCallMgr
    sipp<==========/ \___400<==/
    [400]

    now the problem is call is ok, but when i want to show trunk status:

    CallManager*CLI> dahdi show channels
    Chan Extension Context Language MOH Interpret
    pseudo default default
    1 from-pstn default
    2 400 from-pstn default
    3 from-pstn default
    4 401 from-pstn default
    5 from-pstn default
    6 402 from-pstn default
    7 from-pstn default
    8 403 from-pstn default
    9 from-pstn default
    10 404 from-pstn default
    11 from-pstn default
    12 405 from-pstn default
    13 from-pstn default
    14 406 from-pstn default
    15 from-pstn default
    17 407 from-pstn default
    18 from-pstn default
    19 408 from-pstn default
    20 from-pstn default
    21 409 from-pstn default
    22 from-pstn default
    23 from-pstn default
    24 from-pstn default
    25 from-pstn default
    26 from-pstn default
    27 from-pstn default
    28 from-pstn default
    29 from-pstn default
    30 from-pstn default
    31 from-pstn default

    only show called extension number,
    how can i show the calling number, because i may misunderstand the blank channel is idle, but actually it is occupied by calls.

    while when i show the E1 channels in ciscoCallMgr(cisco 2600):

    Router#show isdn act
    --------------------------------------------------------------------------------
    ISDN ACTIVE CALLS
    --------------------------------------------------------------------------------
    Call Calling Called Remote Seconds Seconds Seconds Charges
    Type Number Number Name Used Left Idle Units/Crcy
    --------------------------------------------------------------------------------
    Out 372 472 17 0 0 0
    In 334 434 17 0 0
    Out 373 473 15 0 0 0
    In 335 435 15 0 0
    Out 374 474 14 0 0 0
    In 336 436 14 0 0
    Out 375 475 14 0 0 0
    In 337 437 14 0 0
    Out 376 476 9 0 0 0
    In 338 438 9 0 0
    Out 377 477 9 0 0 0
    In 339 439 9 0 0
    Out 379 479 2 0 0 0
    In 340 440 2 0 0
    Out 378 478 2 0 0 0
    In 341 441 2 0 0
    --------------------------------------------------------------------------------
     
  2. callmgr

    Joined:
    May 12, 2009
    Messages:
    4
    Likes Received:
    0
    previous post miss format, follow is repost:

    CallManager*CLI> dahdi show channels
    Chan Extension Context Language MOH Interpret
    pseudo default default
    1 from-pstn default
    2 400 from-pstn default
    3 from-pstn default
    4 401 from-pstn default
    5 from-pstn default
    6 402 from-pstn default
    7 from-pstn default
    8 403 from-pstn default
    9 from-pstn default
    10 404 from-pstn default
    11 from-pstn default
    12 405 from-pstn default
    13 from-pstn default
    14 406 from-pstn default
    15 from-pstn default
    17 407 from-pstn default
    18 from-pstn default
    19 408 from-pstn default
    20 from-pstn default
    21 409 from-pstn default
    22 from-pstn default
    23 from-pstn default
    24 from-pstn default
    25 from-pstn default
    26 from-pstn default
    27 from-pstn default
    28 from-pstn default
    29 from-pstn default
    30 from-pstn default
    31 from-pstn default
     
  3. Redfone

    Joined:
    Jul 12, 2007
    Messages:
    177
    Likes Received:
    0
    Try setting 'pri intense debug span 1' on your Elastix E1. This should show all D-chan information being passed between Elastix and the Cisco including CID values.

    Good luck,
    Redfone Communications LLC
     

Share This Page