HELP unable to make/receive calls onmy A400P FXO

Discussion in 'General' started by yesmat, Oct 28, 2009.

  1. yesmat

    Joined:
    Mar 16, 2009
    Messages:
    103
    Likes Received:
    0
    Hi,

    I have a new Elastix 1.5.2 installation with a A400P card 4-port FXO card.

    I can't dial out or receive calls using the card. There is green light at each of the ports at the back of the card and I believe the driver is installed correctly as per the below.

    I have changed the context from "from-pstn" to "from-zaptel" based on recommendation from "Elastix without Tears" pdf. But even when I change back to "from-pstn" I am still unable to use the card.

    when i dial out I get the message "All channels are busy now...." when I dial in there is no debugging messages on the Asterisk console at all as if there is no cable connected. I have tested the POTS lines with the Telco provider and they all work ok with a normal phone and also with the old NEC PBX.

    Need some urgent support. Thanks

    [root@pbx ~]# service dahdi status
    ### Span 1: WCTDM/4 "Wildcard TDM400P REV E/F Board 5" (MASTER)
    1 FXO FXSKS (In use) (EC: OSLEC) RED
    2 FXO FXSKS (In use) (EC: OSLEC) RED
    3 FXO FXSKS (In use) (EC: OSLEC) RED
    4 EMPTY

    pbx*CLI> dahdi show channels
    Chan Extension Context Language MOH Interpret
    pseudo default default
    1 from-zaptel en default
    2 from-zaptel en default
    3 from-zaptel en default

    [root@pbx asterisk]# cat dahdi-channels.conf
    ; Autogenerated by /usr/sbin/dahdi_genconf on Wed Oct 28 11:14:59 2009 -- do not hand edit
    ; Dahdi Channels Configurations (chan_dahdi.conf)
    ;
    ; This is not intended to be a complete chan_dahdi.conf. Rather, it is intended
    ; to be #include-d by /etc/chan_dahdi.conf that will include the global settings
    ;

    ; Span 1: WCTDM/4 "Wildcard TDM400P REV E/F Board 5" (MASTER)
    ;;; line="1 WCTDM/4/0 FXSKS (In use) (EC: OSLEC)"
    signalling=fxs_ks
    callerid=asreceived
    group=0
    context=from-zaptel
    channel => 1
    callerid=
    group=
    context=default

    ;;; line="2 WCTDM/4/1 FXSKS (In use) (EC: OSLEC)"
    signalling=fxs_ks
    callerid=asreceived
    group=0
    context=from-zaptel
    channel => 2
    callerid=
    group=
    context=default

    ;;; line="3 WCTDM/4/2 FXSKS (In use) (EC: OSLEC)"
    signalling=fxs_ks
    callerid=asreceived
    group=0
    context=from-zaptel
    channel => 3
    callerid=
    group=
    context=default


    [root@pbx asterisk]# cat chan_dahdi.conf
    ;# Flash Operator Panel will parse this file for dahdi trunk buttons
    ;# AMPLABEL will be used for the display labels on the buttons

    ;# %c Dahdi Channel number
    ;# %n Line number
    ;# %N Line number, but restart counter
    ;# Example:
    ;# ;AMPLABEL:Channel %c - Button %n

    ;# For Dahdi/* buttons use the following
    ;# (where x=number of buttons to dislpay)
    ;# ;AMPWILDCARDLABEL(x):MyLabel


    [channels]
    language=en

    ; include dahdi extensions defined in FreePBX

    #include dahdi-channels.conf
    #include chan_dahdi_additional.conf

    ; XTDM20B Port #1,2 plugged into PSTN
    ;AMPLABEL:Channel %c - Button %n
    ;context=from-pstn
    context=from-zaptel
    signalling=fxs_ks
    faxdetect=incoming
    usecallerid=yes
    echocancel=yes
    ;useincommingcalleridonzaptransfer=yes
    echocancelwhenbridged=no
    ;echotraining=800
    group=0
    channel=1-2

    My Elastix configs have an inbound rule ANY/ANY goes to a specific extension which is already registered to the server,
     

Share This Page