Feature code with Lisksys phones

Discussion in 'IP Phones' started by itjumper, Oct 3, 2008.

  1. itjumper

    Joined:
    Jul 22, 2008
    Messages:
    81
    Likes Received:
    0
    I use Grandstream, Polycom and LinkSys IP phones. When I dial from Grandstream and Polycom phones, intercom works fine. For instance, when I dial *801001, extension 1001 will auto answer with speaker on. I can see *801001 being dialed in asterisk console.

    But when I dial *801001 from a Linksys phone, only *80 is being passed to asterisk. This happens to all feature codes. Looks like only 3 characters (*80) are being sent from the LinkSys phone. Any help would be appreciated.


    -- Executing [*80@itjumper:1] Goto("SIP/1004-b7a02870", "itjumper_rulematch|*80|1") in new stack
    -- Goto (itjumper_rulematch,*80,1)
    -- Executing [*80@itjumper_rulematch:1] ResetCDR("SIP/1004-b7a02870", "") in new stack
    -- Executing [*80@itjumper_rulematch:2] NoCDR("SIP/1004-b7a02870", "") in new stack
    -- Executing [*80@itjumper_rulematch:3] Wait("SIP/1004-b7a02870", "1") in new stack
    -- Executing [*80@itjumper_rulematch:4] Playback("SIP/1004-b7a02870", "silence/1&feature-not-avail-line&silence/1&cannot-complete-as-dialed&check-number-dial-again|noanswer") in new stack
    -- <SIP/1004-b7a02870> Playing 'silence/1' (language 'en')
    -- <SIP/1004-b7a02870> Playing 'feature-not-avail-line' (language 'en')
    == Spawn extension (itjumper_rulematch, *80, 4) exited non-zero on 'SIP/1004-b7a02870'
    -- Executing [h@itjumper_rulematch:1] Macro("SIP/1004-b7a02870", "hangupcall|") in new stack
    -- Executing [s@macro-hangupcall:1] ResetCDR("SIP/1004-b7a02870", "w") in new stack
    -- Executing [s@macro-hangupcall:2] NoCDR("SIP/1004-b7a02870", "") in new stack
    -- Executing [s@macro-hangupcall:3] GotoIf("SIP/1004-b7a02870", "1?skiprg") in new stack
    -- Goto (macro-hangupcall,s,6)
    -- Executing [s@macro-hangupcall:6] GotoIf("SIP/1004-b7a02870", "1?skipblkvm") in new stack
    -- Goto (macro-hangupcall,s,9)
    -- Executing [s@macro-hangupcall:9] GotoIf("SIP/1004-b7a02870", "1?theend") in new stack
    -- Goto (macro-hangupcall,s,11)
    -- Executing [s@macro-hangupcall:11] Hangup("SIP/1004-b7a02870", "") in new stack
    == Spawn extension (macro-hangupcall, s, 11) exited non-zero on 'SIP/1004-b7a02870' in macro 'hangupcall'
    == Spawn extension (macro-hangupcall, s, 11) exited non-zero on 'SIP/1004-b7a02870'
     
  2. Chilling_Silence

    Joined:
    Sep 23, 2008
    Messages:
    488
    Likes Received:
    0
    Hi itjumper,

    Basically if you log into the Web Interface of your SPAXXXX device (Same for using SPA2102's etc with Asterisk / Elastix), then you need to remove the Feature codes from in there. *80 is set to do something like set CFB. Check under the Regional tab of the phones interface and see if you have any luck
     

Share This Page