Fax internally

Discussion in 'General' started by xhal99104, Feb 16, 2008.

  1. xhal99104

    Joined:
    Feb 17, 2007
    Messages:
    15
    Likes Received:
    0
    Hi

    My elastix is now 1.0 (freepbx 2.4 upgraded via the unembedded freepbx menu)

    I'm sorry, but I have tried and tried to fax between two local IAX numbers and to fax to an external fax. I cannot get it to work, but I receive faxes perfectly.
    When I submit a fax to the Hylafax printer I get a job ID in return and seconds later Asterisk starts to make the fax call. The modems seems to connect for a few seconds and then it hangs up again!!:angry: I had an idea that it was about the codec so i forced my provider to use alaw and ulaw only which have been working in earlier versions of elastix.

    It seems that as soon as the actual fax is supposed to be sent, elastix disconnects again.
    Pls any ideas? The mail I receive as confirmation of the failed fax below:

    External:
    Your job to xxx99311 failed because:




    ---- Transcript of session follows ----

    Feb 15 22:12:25.70: [10311]: SESSION BEGIN 000000045 5930486999311
    Feb 15 22:12:25.70: [10311]: HylaFAX (tm) Version 4.3.3
    Feb 15 22:12:25.70: [10311]: SEND FAX: JOB 7 DEST xxx99311 COMMID 000000045 DEVICE '/dev/ttyIAX2' FROM '9002 <xxxx.dk>' USER 9002
    Feb 15 22:12:25.70: [10311]: STATE CHANGE: RUNNING -> SENDING
    Feb 15 22:12:25.70: [10311]: <-- [12:AT+FCLASS=1\r] Feb 15 22:12:25.71: [10311]: --> [2]
    Feb 15 22:12:25.72: [10311]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
    Feb 15 22:12:25.72: [10311]: DIAL xxx99311
    Feb 15 22:12:25.72: [10311]: <-- [13:ATDT86999311\r] Feb 15 22:12:46.45: [10311]: --> [7]
    Feb 15 22:12:48.17: [10311]: --> HDLC<25:FF C0 02 04 04 04 04 04 04 04 04 04 8C 8C CC 9C 9C 9C 6C 1C 1E 86 62 8A B7>
    Feb 15 22:12:48.17: [10311]: --> [2]
    Feb 15 22:12:48.17: [10311]: REMOTE CSI "Faxxxx99311"
    Feb 15 22:12:48.17: [10311]: <-- [9:AT+FRH=3\r]
    Feb 15 22:12:48.19: [10311]: --> [7]
    Feb 15 22:12:48.63: [10311]: --> HDLC<8:FF C8 01 00 77 1E 80 40>
    Feb 15 22:12:48.69: [10311]: --> [2]
    Feb 15 22:12:48.69: [10311]: REMOTE best rate 14400 bit/s
    Feb 15 22:12:48.69: [10311]: REMOTE max A4 page width (215 mm)
    Feb 15 22:12:48.69: [10311]: REMOTE max unlimited page length
    Feb 15 22:12:48.69: [10311]: REMOTE best vres 7.7 line/mm
    Feb 15 22:12:48.69: [10311]: REMOTE format support: MH, MR
    Feb 15 22:12:48.69: [10311]: REMOTE best 0 ms/scanline
    Feb 15 22:12:48.69: [10311]: USE 14400 bit/s
    Feb 15 22:12:48.69: [10311]: <-- [9:AT+FTH=3\r]
    Feb 15 22:12:48.69: [10311]: --> [7]
    Feb 15 22:12:48.69: [10311]: <-- HDLC<3:FF C8 DF> Feb 15 22:12:49.87: [10311]: --> [2]
    Feb 15 22:12:49.87: [10311]: MODEM input buffering enabled
    Feb 15 22:12:49.87: [10311]: <-- [5:ATH0\r]
    Feb 15 22:12:49.97: [10311]: --> [2]
    Feb 15 22:12:49.97: [10311]: MODEM set DTR OFF
    Feb 15 22:12:49.97: [10311]: MODEM set baud rate: 0 baud (flow control unchanged)
    Feb 15 22:12:49.97: [10311]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
    Feb 15 22:12:49.97: [10311]: SESSION END

    ------- Unsent job status -------
    Destination: xxx999311
    JobID: 7
    GroupID: 7
    Sender: 9002
    Mailaddr: xxxxx.dk
    CommID: 000000045
    Modem: ttyIAX2
    Submitted From: rdfhada.xxxxx
    Page Width: 209 (mm)
    Page Length: 296 (mm)
    Resolution: 196 (lpi)
    Status:
    Dialogs: 1
    Dials: 0
    Calls: 1
    Pages: 0
    TotPages: 0
    Attempts: 0
    Dirnum:


    And the internal from 9002 to 9001:
    Your job to 9001 failed because:




    ---- Transcript of session follows ----

    Feb 15 22:12:02.24: [10228]: SESSION BEGIN 000000043 593049001
    Feb 15 22:12:02.24: [10228]: HylaFAX (tm) Version 4.3.3
    Feb 15 22:12:02.25: [10228]: SEND FAX: JOB 6 DEST 9001 COMMID 000000043 DEVICE '/dev/ttyIAX2' FROM '9002 <xxx.dk>' USER 9002
    Feb 15 22:12:02.25: [10228]: STATE CHANGE: RUNNING -> SENDING
    Feb 15 22:12:02.26: [10228]: <-- [12:AT+FCLASS=1\r] Feb 15 22:12:02.27: [10228]: --> [2]
    Feb 15 22:12:02.27: [10228]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
    Feb 15 22:12:02.27: [10228]: DIAL 9001
    Feb 15 22:12:02.27: [10228]: <-- [9:ATDT9001\r]
    Feb 15 22:12:07.23: [10228]: --> [7]
    Feb 15 22:12:09.07: [10228]: --> HDLC<34:FF C0 04 B5 00 AA 12 9E 36 86 62 82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 2C 74 CC 74 CC DA 7F>
    Feb 15 22:12:09.07: [10228]: --> [2]
    Feb 15 22:12:09.07: [10228]: REMOTE NSF "AD 00 55 48 79 6C 61 46 41 58 20 28 74 6D 29 20 56 65 72 73 69 6F 6E 20 34 2E 33 2E 33"
    Feb 15 22:12:09.07: [10228]: NSF remote fax equipment: HylaFAX
    Feb 15 22:12:09.07: [10228]: NSF remote station ID: "HylaFAX (tm) Version 4.3.3"
    Feb 15 22:12:09.07: [10228]: <-- [9:AT+FRH=3\r]
    Feb 15 22:12:09.09: [10228]: --> [7]
    Feb 15 22:12:09.89: [10228]: --> HDLC<25:FF C0 02 1A 82 62 04 76 A6 CE B6 F6 16 2A 04 36 A6 86 16 C6 96 B2 04 AD 11>
    Feb 15 22:12:09.89: [10228]: --> [2]
    Feb 15 22:12:09.89: [10228]: REMOTE CSI "Michael Thomsen FAX"
    Feb 15 22:12:09.89: [10228]: <-- [9:AT+FRH=3\r] Feb 15 22:12:09.93: [10228]: --> [7]
    Feb 15 22:12:10.47: [10228]: --> HDLC<15:FF C8 01 00 73 5F 23 01 FB C1 01 01 18 90 61>
    Feb 15 22:12:10.53: [10228]: --> [2]
    Feb 15 22:12:10.53: [10228]: REMOTE best rate 9600 bit/s Feb 15 22:12:10.53: [10228]: REMOTE max A3 page width (303 mm)
    Feb 15 22:12:10.53: [10228]: REMOTE max unlimited page length Feb 15 22:12:10.53: [10228]: REMOTE best vres R16 x 15.4 line/mm
    Feb 15 22:12:10.53: [10228]: REMOTE format support: MH, MR, MMR
    Feb 15 22:12:10.53: [10228]: REMOTE supports T.30 Annex A, 256-byte ECM
    Feb 15 22:12:10.53: [10228]: REMOTE best 0 ms/scanline
    Feb 15 22:12:10.53: [10228]: USE 9600 bit/s
    Feb 15 22:12:10.53: [10228]: USE error correction mode
    Feb 15 22:12:10.53: [10228]: <-- [9:AT+FTH=3\r]
    Feb 15 22:12:10.54: [10228]: --> [7]
    Feb 15 22:12:10.54: [10228]: <-- HDLC<3:FF C8 DF> Feb 15 22:12:11.72: [10228]: --> [2]
    Feb 15 22:12:11.72: [10228]: MODEM input buffering enabled
    Feb 15 22:12:11.72: [10228]: <-- [5:ATH0\r]
    Feb 15 22:12:11.83: [10228]: --> [2]
    Feb 15 22:12:11.83: [10228]: MODEM set DTR OFF
    Feb 15 22:12:11.83: [10228]: MODEM set baud rate: 0 baud (flow control unchanged)
    Feb 15 22:12:11.83: [10228]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
    Feb 15 22:12:11.83: [10228]: SESSION END

    ------- Unsent job status -------
    Destination: 9001
    JobID: 6
    GroupID: 6
    Sender: 9002
    Mailaddr: xxxx.dk
    CommID: 000000043
    Modem: ttyIAX2
    Submitted From: rxxxxxxxhl.dk
    Page Width: 209 (mm)
    Page Length: 296 (mm)
    Resolution: 196 (lpi)
    Status:
    Dialogs: 1
    Dials: 0
    Calls: 1
    Pages: 0
    TotPages: 0
    Attempts: 0
    Dirnum:


    Sorry for the long message, but can anyone help?

    Tks in advance

    Rgds
    Michael
     
  2. xhal99104

    Joined:
    Feb 17, 2007
    Messages:
    15
    Likes Received:
    0
    asterisk reports this:
    Spawn extension (macro-hangupcall, s, 11) exited non-zero on 'SIP/46932577-09e9e888'
     
  3. xhal99104

    Joined:
    Feb 17, 2007
    Messages:
    15
    Likes Received:
    0
    pls if anyone can help on the fax topic cause I´m lost.

    Rgds Michael
     
  4. bulgarion

    Joined:
    Feb 22, 2008
    Messages:
    38
    Likes Received:
    0
    Have the same issue, followed the Video Tutorial for the 1.0 alpha version, and I get the iaxmodem answering to fax calls (internals AND externals), but somehow the call is treated as a voice stream and not fax data - in the /var/log/message I have similar informations. It seems quite a bug, or perhaps incorrect configuration, as soon as the Bug Tracking System will be back online I'll put it in.
     

Share This Page