Elastix 1.1 not detecting Sangoma a200

Discussion in 'General' started by samix4u, Jun 24, 2008.

  1. samix4u

    Joined:
    Mar 31, 2008
    Messages:
    20
    Likes Received:
    0
    Hay i install v1.1 now my sangoma a200 card not detecting when i enter "wancfg_zaptel" it says wanpipe...... not found.:( after again installed v1.0-17 then it working perfectly.:eek:hmy: can any one help me to sort this isse. :dry:
     
  2. elastixguy

    Joined:
    Mar 1, 2008
    Messages:
    36
    Likes Received:
    0
    I have a similar setup, with Sangoma A200 running on Elastix v1.0-17.

    I was planning to upgrade to v1.1, but now that you mentioned this issue I might hold a little.

    Something I would try (if you haven't yet) is to attempt the manual installation, as described here:

    http://wiki.sangoma.com/elastix-rpms

    If it still doesn't work, you might wanna check for irq conflicts or something of that sort.

    If you still can't figure it out, you might wanna downgrade back to v1.0 and wait a bit until Sangoma mentions on their page that Elastix v1.1 is fully supported. You could even send an email to support@sangoma.com and hurry them to release new rpms for Elastix v1.1.

    I'd appreciate to know how it turns out for you. Keep us posted.


    Regards
     
  3. cowboy47

    Joined:
    Jun 14, 2007
    Messages:
    276
    Likes Received:
    0
    any results on this?
     
  4. elastixguy

    Joined:
    Mar 1, 2008
    Messages:
    36
    Likes Received:
    0
    It seems Sangoma have just updated their wiki to include some instructions for Elastix v1.1 (check the link on my first reply).

    Once again Sangoma has lived up to their reputation of great support. Keep up the good work, guys!

    samix4u, please let us know if it worked for you.<br><br>Post edited by: elastixguy, at: 2008/06/27 02:04
     
  5. samix4u

    Joined:
    Mar 31, 2008
    Messages:
    20
    Likes Received:
    0
    Yes they add new wanpipe. i'll check and let you know.
    Thanks for your help.
     
  6. samix4u

    Joined:
    Mar 31, 2008
    Messages:
    20
    Likes Received:
    0
    It working man what i did is downloaded and run both file.

    cool it detect my card smoothly
    1.cd

    #>cd /usr/src

    2.download

    #>wget ftp://ftp.sangoma.com/linux/RPMS/Elasti ... 0.i686.rpm

    #>wget ftp://ftp.sangoma.com/linux/RPMS/Elasti ... 0.i686.rpm


    3. install

    #>rpm -i --force wanpipe-modules-2.6.18-53.1.19.el5-3.2.6-0.i686.rpm

    #>rpm -i --force wanpipe-util-3.2.6-0.i686.rpm


    4. Configuring Card

    Use wancfg_zaptel utility to configure the card. Follow on screen instruction to configure the card.
    [root@elastix ~]# wancfg_zaptel
     
  7. meerkat746

    Joined:
    Jul 10, 2008
    Messages:
    1
    Likes Received:
    0
    I for one are ever grateful that you did this post. I'm new to Linux, and new to Elastix (been legacy techie for 17 years) and this post has saved me hours and a few million hairs (dun have much left anyway).

    So from the bottom of my heart, THANK YOU!!!!!!
     

Share This Page