Como configurar Troncal Placa Digium TDM2400P

ivanber

Joined
Nov 14, 2010
Messages
10
Likes
0
Points
0
#1
Tengo un problema para configurar un troncal
tengo 8 lineas conectactadas a la placa pero no puedo lograr que la 6 linea tenga salida pero si entran las llamadas el error que me da es que las lineas se encuentran ocupadas

aclaro que el troncal de la linea 2 3 actualmente si tienen salida. cual sera el problema adjunto los archivos.

chan_dahdi.conf

; Auto-generated by /usr/sbin/hardware_detector
[trunkgroups]

[channels]
context=from-zaptel
signalling=fxs_ks
rxwink=300 ; Atlas seems to use long (250ms) winks
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
canpark=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=no
faxdetect=incoming
echotraining=800
rxgain=0.0
txgain=0.0
callgroup=1
pickupgroup=1

;Uncomment these lines if you have problems with the disconection of your analog lines
busydetect=yes
busycount=6
immediate=yes

callerid=asreceived
group=0
channel => 1-8



#include dahdi-channels.conf
#include chan_dahdi_additional.conf


dahdi-channels.conf
; Autogenerated by /usr/sbin/dahdi_genconf on Mon Mar 21 22:21:52 2011
; If you edit this file and execute /usr/sbin/dahdi_genconf again,
; your manual changes will be LOST.
; Dahdi Channels Configurations (chan_dahdi.conf)
;
; This is not intended to be a complete chan_dahdi.conf. Rather, it is intended
; to be #include-d by /etc/chan_dahdi.conf that will include the global settings
;

; Span 1: WCTDM/0 "Wildcard TDM2400P Board 1" (MASTER)
;;; line="1 WCTDM/0/0 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-zaptel
channel => 1
callerid=
group=
context=default

;;; line="2 WCTDM/0/1 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-zaptel
channel => 2
callerid=
group=
context=default

;;; line="3 WCTDM/0/2 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-zaptel
channel => 3
callerid=
group=
context=default

;;; line="4 WCTDM/0/3 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-zaptel
channel => 4
callerid=
group=
context=default

;;; line="5 WCTDM/0/4 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-zaptel
channel => 5
callerid=
group=
context=default

;;; line="6 WCTDM/0/5 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-zaptel
channel => 6
callerid=
group=
context=default

;;; line="7 WCTDM/0/6 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-zaptel
channel => 7
callerid=
group=
context=default

;;; line="8 WCTDM/0/7 FXSKS"
signalling=fxs_ks
callerid=asreceived
group=0
context=from-zaptel
channel => 8
callerid=
group=
context=default
system.conf
# Autogenerated by /usr/sbin/dahdi_genconf on Mon Mar 21 22:21:52 2011
# If you edit this file and execute /usr/sbin/dahdi_genconf again,
# your manual changes will be LOST.
# Dahdi Configuration File
#
# This file is parsed by the Dahdi Configurator, dahdi_cfg
#
# Span 1: WCTDM/0 "Wildcard TDM2400P Board 1" (MASTER)
fxsks=1-8
echocanceller=mg2,1-8



# Global data

loadzone = us
defaultzone = us
 

Luis Diego

Joined
Nov 1, 2010
Messages
237
Likes
0
Points
0
#2
Te encuentras en
loadzone = us
defaultzone = us???

y que signaling estan manejando por alla.
 

fmvillares

Joined
Sep 8, 2007
Messages
1,785
Likes
0
Points
0
#3
la linea 6 seguro algun problema tiene no sera solo de entrada con tono diferente o una linea con voicemail y stutter tone...???
 

chagudelo

Joined
Jul 10, 2012
Messages
1
Likes
0
Points
0
#4
Hola,

Acabo de instalar una TDM2400P, y tengo un problema similar, no es posible marcar... configuré la trocal que trae por defecto (ZAP g0) y creo una ruta de salida, pero siempre me indica que el circuito se encuentra ocupado.

¿Logró solucionar el problema?, ¿me puede compartir la solución?

Muchas gracias.
 

jgutierrez

Joined
Feb 28, 2008
Messages
5,737
Likes
0
Points
0
#5
Y ya detectaste la tarjeta?
Sistema -> Hardware Detector
(avanzado -> reemplazar chan_dahdi)

Luego de haber ejecutado eso, pega la salida de:
lspci
uname -a
rpm -qa | grep dahdi | sort
lsdahdi
asterisk -rx "dahdi show channels"
cat /etc/asterisk/chan_dahdi.conf
cat /etc/asterisk/dahdi-channels.conf
 

Members online

No members online now.

Latest posts

Forum statistics

Threads
30,900
Messages
130,884
Members
17,561
Latest member
marouen
Top