After IAXMODEM update i can't send faxes.

Discussion in 'General' started by kawa636r, Jan 28, 2009.

  1. kawa636r

    Joined:
    Oct 25, 2007
    Messages:
    36
    Likes Received:
    0
    Hi,

    i use elastix with a te405p for sending faxes, but in the last days i've see that the versions of hylafax and of iaxmodems was too much old.

    I have updated hylafax with hylafax+ and all was ok, but when i have updated iaxmodem, i can't send faxes anymore.

    THIS IT'S a fax trasmission log :


    Jan 28 18:02:30.86: [ 3300]: SESSION BEGIN 000002456 +***********
    Jan 28 18:02:30.86: [ 3300]: HylaFAX (tm) Version 5.2.8
    Jan 28 18:02:30.86: [ 3300]: SEND FAX: JOB 4257 DEST ************COMMID 000002456 DEVICE '/dev/ttyIAX10' FROM '*******************************' USER ************
    Jan 28 18:02:30.86: [ 3300]: STATE CHANGE: RUNNING -> SENDING
    Jan 28 18:02:30.86: [ 3300]: <-- [12:AT+FCLASS=1\r]
    Jan 28 18:02:30.86: [ 3300]: --> [2]
    Jan 28 18:02:30.86: [ 3300]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
    Jan 28 18:02:30.88: [ 3300]: DIAL 0916850694
    Jan 28 18:02:30.88: [ 3300]: <-- [15:ATDT02******\r]
    Jan 28 18:02:43.04: [ 3300]: --> [7]
    Jan 28 18:02:44.77: [ 3300]: --> [10:NO CARRIER]
    Jan 28 18:02:44.77: [ 3300]: MODEM No carrier
    Jan 28 18:02:44.77: [ 3300]: <-- [10:AT+FRS=21\r]
    Jan 28 18:02:44.77: [ 3300]: --> [5]
    Jan 28 18:02:44.77: [ 3300]: MODEM Command error
    Jan 28 18:02:44.77: [ 3300]: Failure to receive silence (synchronization failure). {E100}
    Jan 28 18:02:44.77: [ 3300]: <-- [9:AT+FRS=7\r]
    Jan 28 18:02:44.77: [ 3300]: --> [5]
    Jan 28 18:02:44.77: [ 3300]: MODEM Command error
    Jan 28 18:02:44.77: [ 3300]: Failure to receive silence (synchronization failure). {E100}
    Jan 28 18:02:44.77: [ 3300]: <-- [9:AT+FRH=3\r]
    Jan 28 18:02:44.77: [ 3300]: --> [5]
    Jan 28 18:02:44.77: [ 3300]: MODEM Command error
    Jan 28 18:02:44.77: [ 3300]: No receiver protocol (T.30 T1 timeout) {E126}
    Jan 28 18:02:44.77: [ 3300]: SEND FAILED: JOB 4257 DEST 02********** ERR No receiver protocol (T.30 T1 timeout) {E126}
    Jan 28 18:02:44.77: [ 3300]: <-- [9:AT+FRS=7\r]
    Jan 28 18:02:44.77: [ 3300]: --> [5]
    Jan 28 18:02:44.77: [ 3300]: MODEM Command error
    Jan 28 18:02:44.77: [ 3300]: Failure to receive silence (synchronization failure). {E100}
    Jan 28 18:02:44.77: [ 3300]: <-- [9:AT+FTH=3\r]
    Jan 28 18:02:44.77: [ 3300]: --> [5]
    Jan 28 18:02:44.77: [ 3300]: MODEM input buffering enabled
    Jan 28 18:02:45.77: [ 3300]: <-- [5:ATH0\r]
    Jan 28 18:02:45.87: [ 3300]: --> [2]
    Jan 28 18:02:45.87: [ 3300]: MODEM set DTR OFF
    Jan 28 18:02:45.87: [ 3300]: MODEM set baud rate: 0 baud (flow control unchanged)
    Jan 28 18:02:45.87: [ 3300]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
    Jan 28 18:02:45.87: [ 3300]: SESSION END


    i have tried many versions of hylafax but the issue doesn't change.

    i have tried many versions of iaxmodem and the only that works it's the one that comes with the elastix, the 0.0.14 .

    How can i fix this problem ?
     
  2. kawa636r

    Joined:
    Oct 25, 2007
    Messages:
    36
    Likes Received:
    0
    I don't know why it's posted too much long...
     

Share This Page